Anatomical and Physico-Mechanical Properties of Ficus exasperata Vahl Wood
DOI:
https://doi.org/10.14738/dafs.122.16904Keywords:
anatomy, compressive strength, density Ficus exasperata, hardness, shear strength, static bendingAbstract
Most of the commercial timber in Ghana are getting extinct thereby posing a big challenge to the timber industry. There is therefore the need to determine the properties of some of the lesser-used and lesser-known timber species available in the Ghanaian forest for utilization. This study was carried out at Council for Scientific and Industrial Research-Forestry Research Institute of Ghana campus to evaluate the suitability of some anatomical, physical, and mechanical properties of timber obtained from Ficus exasperata trees and its utilization potential in the timber industry. Two trees were extracted and the logs from them were processed into beams. Boards were prepared from these beams and test specimens were prepared for the determination of physical (density), anatomical (fibre measurement, number of vessels, vessel width, vessel diameter) and mechanical (bending, compression, shear, hardness) properties based on internationally acceptable standards. At an average moisture content of 12.16%, the result obtained indicate that the mean values for the properties tested increased from the butt to the top sections of the two trees. However, there was no significant variation in the mean values obtained for the static bending, compression parallel to the grain and shear properties of the middle and top sections of both trees, whereas these properties varied significantly at the butt section of both trees. Generally, the properties tested increased with age from the top to the butt. Thirty-one-year-old F. exasperata recorded an average density of 414.34 kg/m3 whereas the twenty-seven-year-old recorded 385.35 kg/m3. Among the age gradations, the thirty-one-year-old F. exasperata registered maximum values for the evaluated parameters, namely; anatomical, density, modulus of elasticity, modulus of rupture, compression parallel to the grain, shear and hardness. The results of the study suggest that F. exasperata timber is a low-density wood and hence, can be used as substitute of Alstonia boonei and Hannoa klaineana which are also classified in the D30 strength class. Thus, suitable for the production of particleboards, mouldings, core veneer for plywood, boxes, crates, packing cases, pencil, food containers, light furniture industry and other fitments. Hence, it should be promoted in the timber industry.
References
Adewole, S. O., Adenowo, T. K., Naicker, T., & Ojewole, J. A. (2011). Hypoglycaemic and hypotensive effects of Ficus exasperata Vahl. (Moraceae) leaf aqueous extracts in rats. African Journal of Traditional, Complementary and Alternative Medicines, 8(3): 275-83.
Akah, P. A., Orisakwe, O. E., Gamaniel, K. S., & Shittu, A. (1998). Evaluation of Nigerian traditional medicines: II. Effects of some Nigerian folk remedies on peptic ulcer. Journal of ethnopharmacology, 62(2), 123-127. https://doi.org/10.1016/S0378-8741(98)00060-9
Amorim, E. P., Longui, E. L., de Faria, R. F. P., Freitas, M. L. M., de Moraes, M. A., Cambuim, J., & de Souza Gonçalves, P. (2021). Anatomical Radial Variation and Density in Wood of Rubber Tree [Hevea brasiliensis (Willd. ex A. Juss.) Muell. Arg.] CLONES. Revista do Instituto Florestal, 33(1), 7-16. https://doi.org/10.24278/2178-5031.202133101
Awaku, F. A. (1994). Anatomical properties of afina (Strombosia glaucescens, var lucida J. Leonard). Ghana Journal of forestry, 1, 30-33.
Bafor, E. E., Omogbai, E. K., & Ozolua, R. I. (2011). Oxytocin inhibiting effect of the aqueous leaf extract of Ficus exasperata (Moraceae) on the isolated rat uterus. Acta Pol Pharm, 68(4), 541-547.
Bafor, E. E., & Igbinuwen, O. (2009). Acute toxicity studies of the leaf extract of Ficus exasperata on haematological parameters, body weight and body temperature. Journal of Ethnopharmacology, 123(2), 302-307. https://doi.org/10.1016/j.jep.2009.03.001
Bahmani, M., Fathi, L., Koch, G., Kool, F., Aghajani, H., & Humar, M. (2020). Heartwood and sapwood features of Sorbus torminalis grown in Iranian forests. Wood Research, 65(2), 195-204. doi.org/10.37763/wr.1336-4561/65.2.195204
Baillie, J., Hilton-Taylor, C., & Stuart, S. N. (Eds.). (2004). 2004 International Union for Conservation of Nature (IUCN) red list of threatened species: a global species assessment. Iucn. Published by IUCN, Gland, Switzerland and Cambridge, UK.
Bakar, B. F. A., Hiziroglu, S. and Tahir, P. M. (2013). Properties of some thermally modified wood species. Materials and Design, 43: 348 -355. https://doi.org/10.1016/j.matdes.2012.06.054
Bhat, K. M., Priya, P. B., & Rugmini, P. (2001). Characterisation of juvenile wood in teak. Wood Science and Technology, 34(6), 517-532. https://doi.org/10.1007/s002260000067
Blackham, G., Núnez del Prado, I., Parker, J., and Tavares de Bastos, C. (2020). Lesser-Known & Lesser-Used Timber Species Utilising Ghana’s Sustainable Timber Resources. BVRio Responsible Timber Exchange
Boadu, K. B., Anokye, R., Afrifah, K. A., Tetteh, E. N., Anning, O. F., & Osei, B. K. (2022). Characterization of the fibre morphology and chemical composition of aged PB 260 and IRCA 41 clones of rubber (Hevea brasiliensis) wood for pulp and paper making. Journal of the Indian Academy of Wood Science, 19(2), 133-140. https://doi.org/10.1007/s13196-022-00304-9
British Standard BS 2568-2 (2002). Structural Use of Timber Part 2: Code of Practice for Permissible Stress Design, Materials and Workmanship. BSI 389 Chiswick High Road London W4 4AL ISBN 0 580 33314 0.
BS EN 338:2016, Structural timber. Strength classes, British Standards Institution, 2016. BS 373:1957. Methods of testing small clear specimens of timber. BS 373:1957 Methods of testing small clear specimens of timber (en-standard.eu)
Chowdhury, M. Q., Ishiguri, F., Hiraiwa, T., Matsumoto, K., Takashima, Y., Iizuka, K. & Yoshizawa, N. (2012). Variation in anatomical properties and correlations with wood density and compressive strength in Casuarina equisetifolia growing in Bangladesh. Australian forestry, 75(2), 95-99. https://doi.org/10.1080/00049158.2012.10676390
Derikvand, M., Kotlarewski, N., Lee, M., Jiao, H., & Nolan, G. (2019). Characterisation of physical and mechanical properties of unthinned and unpruned plantation-grown Eucalyptus nitens H. Deane & Maiden lumber. Forests, 10(2), 194. https://doi.org/10.3390/f10020194
Dickson, W. C. (2000). Integrative Plant Anatomy. Academic Press, San Diego, 533 p. Emmanuel OHEMENG, Prosper MENSAH, Rafael Rodolfo de MELO, Emmanuel EBANYENLE, Francis Wilson
OWUSU, Haruna SEIDU, Stephen Jobson MITCHUAL (2023). Technological properties of Memecylon lateriflorum wood: a timber species from Ghana. Nativa, Sinop, v. 11, n. 3, p. 356-367, 2023. Pesquisas Agrárias e Ambientais. DOI: https://doi.org/10.31413/nativa.v11i3.15885
Francis Wilson Owusu, Kwame Asamoah Adam, Haruna Seidu, Prosper Mensah, James Govina. (2020). Lesser-Known Species; Utilizing Ghana’s Sustainable Timber Resources. BVRio, Forestry Commission, CSIR-Forestry Research Institute of Ghana: Responsible Timber Exchange.
Gallego, A., Ripoll, M. A., Timbolmas, C., Rescalvo, F., Suarez, E., Valverde, I., ... & Merlo, E. (2021). Modulus of elasticity of I-214 young poplar wood from standing trees to sawn timber: influence of the age and stand density. European Journal of Wood and Wood Products, 79, 1225-1239. https://doi.org/10.1007/s00107-021-01675-5
Gil-Moreno, D., Manso, R., O’Ceallaigh, C., & Harte, A. M. (2024). The influence of age on the timber properties and grading of Scots pine and larch in Ireland. Forestry: An International Journal of Forest Research, 97(1), 133-146. https://doi.org/10.1093/forestry/cpad027
Hansen, C. P., Damnyag, L., Obiri, B. D., & Carlsen, K. (2012). Revisiting illegal logging and the size of the domestic timber market: the case of Ghana. International Forestry Review, 14(1), 39-49. https://doi.org/10.1505/146554812799973181
Horáček, P., Fajstavr, M., & Stojanović, M. (2018). The variability of wood density and compression strength of Norway spruce (Picea abies/L./Karst.) within the stem. Beskydy, 10(1-2), 17-26. https://doi.org/10.11118/beskyd201710010017
International Association of Wood Anatomists, IAWA. (1989). List of microscopic features for hardwood identification. International Association of Wood Anatomist, no. 10, pp. 219 - 232. ISO 13061-4 (2114). Physical and Mechanical Properties of Wood. Testing methods for small clear wood specimens. Part 4: Determination of modulus of elasticity in static bending. ISO 13061-4:2014 - Physical and mechanical properties of wood — Test methods for small clear wood specimens — Part 4: Determination of modulus of elasticity in static bending
Jacobsen, A. L., Pratt, R. B., Tobin, M. F., Hacke, U. G., & Ewers, F. W. (2012). A global analysis of xylem vessel length in woody plants. American journal of botany, 99(10), 1583-1591. https://doi.org/10.3732/ajb.1200140
Joseph, B., & Raj, S. J. (2010). Phytopharmacological and phytochemical properties of three Ficus species-an overview. International Journal of Pharma Bio Sciences, 1(4), 246-253.
Kauniste, M., Just, A., Tuhkanen, E., & Kalamees, T. (2024). Assessment on Strength and Stiffness Properties of Aged Structural Timber. Journal of Sustainable Architecture and Civil Engineering, 34(1), 62-74. https://doi.org/10.5755/j01.sace.34.1.35534
Kiaei, M. A. J. I. D. (2013). Technological properties of Iranian cultivated paulownia wood (Paulownia fortunei). Cellulose Chemistry and Technology, 47(9-10), 735-743.
Kretschmann, D. E. (2010). Mechanical properties of wood. Environments, 5, 34. Mechanical Properties of Wood. chapter_05-libre.pdf (d1wqtxts1xzle7.cloudfront.net)
Liu, M., Pan, R., & Tyree, M. T. (2018). Intra-specific relationship between vessel length and vessel diameter of four species with long-to-short species-average vessel lengths: further validation of the computation algorithm. Trees, 32, 51-60. https://doi.org/10.1007/s00468-017-1610-y
Mäkinen, H., Saranpää, P., & Linder, S. (2002). Effect of growth rate on fibre characteristics in Norway spruce (Picea abies (L.) Karst.). https://doi.org/10.1515/HF.2002.070
Mensah, P., R. Rodolfo de Melo, S. J. Mitchual, J. Govina and H. Seidu (2021). Characterisation and Utilisation of Theobroma Cacao Stem Wood. Ghana Journal of Forestry, Vol. 37, 2021, 79 – 99.
Migneault, S., Koubaa, A., Erchiqui, F., Chaala, A., Englund, K., Krause, C. and Wolcott, M. (2008). Effect of Fiber Length on Processing and Properties of Extruded Wood-Fiber/HDPE Composites. Journal of Applied Polymer Science, Vol. 110, 1085–1092.
Mitchual, S. J., Mensah, P., Frimpong-Mensah, K. and Appiah-Kubi, E. (2020). Characterization of Particleboard Produced from Residues of Plantain pseudostem, Cocoa Pod and Stem and Ceiba. Materials Sciences and Applications, 11, 817-836. https://doi.org/10.4236/msa.2020.1112054
Monteoliva, S., Senisterra, G., Marquina, J. L., Marlats, R. M. and Ciocchini, G. R. (2002). Clones de sauce, longitud de fibras en su madera. Rev. FCA UNCuyo, Tomo XXXIV, (2): 49–56.
Moraes, L. G., Lima, M. D. R., Assis-Pereira, G., de Almeida Gonçalves, D., Vidaurre, G. B., Bufalino, L., & de Paula Protásio, T. (2023). Forking and planting spacing impacts on wood density, X-ray density, and heartwood proportion of Tachigali vulgaris. Trees, 37(5), 1567-1581. https://doi.org/10.1007/s00468-023-02443-z
Nenning, T., Tockner, A., Konnerth, J., Gindl-Altmutter, W., Grabner, M., Hansmann, C., & Pramreiter, M. (2024). Variability of mechanical properties of hardwood branches according to their position and inclination in the tree. Construction and Building Materials, 419, 135448. https://doi.org/10.1016/j.conbuildmat.2024.135448
Ofori, J., Brentuo, B., Mensah, M., Mohammed, A. I., & Boamah-Tawiah, R. (2009). Properties of 10 Ghanaian high density lesser-used-species of importance to bridge construction. Part 1: green moisture content, basic density and shrinkage characteristics. Ghana Journal of Forestry, 25, 67-77.
Oladosu, I. A., Zubair, M. F., Ali, M. S., & Olawore, N. O. (2009). Anticandidal activity of volatile compounds from the root bark of Ficus exasperata Vahl-Holl (Moraceae). Journal of Essential Oil Bearing Plants, 12(5), 562-568. https://doi.org/10.1080/0972060X.2009.10643758
Ogasa, M., Miki, N., & Yoshikawa, K. (2010). Changes of hydraulic conductivity during dehydration and rehydration in Quercus serrata Thunb. and Betula platyphylla var. japonica Hara: the effect of xylem structures. Tree physiology, 30(5), 608-617. https://doi.org/10.1093/treephys/tpq011
Olson, M. E., Anfodillo, T., Rosell, J. A., Petit, G., Crivellaro, A., Isnard, S., & Castorena, M. (2014). Universal hydraulics of the flowering plants: vessel diameter scales with stem length across angiosperm lineages, habits and climates. Ecology Letters, 17(8), 988-997. https://doi.org/10.1111/ele.12302
Peszlen, I. (1994). Influence of age on selected anatomical properties of Populus clones. IAWA journal, 15(3), 311-321.
San, P. H., Long, K. L., Zhang, Z. C., Hui, C. T., Seng, Y. W., Lin, S. F., Hun, T. A. and Fong, K. W., (2016). Anatomical Features, Fiber Morphological, Physical and Mechanical Properties of Three Years Old New Hybrid Paulownia: Green Paulownia. Research Journal of Forestry, 10: 30-35.
Saravanan, V., Parthiban, K. T., Thiruneraiselvan, S., Kumar, P., Vennila, S., & Kanna, S. U. (2014). Comparative study of wood physical and mechanical properties of Melia dubia with Tectona grandis at different Age Gradation. Research Journal of Recent Sciences ISSN, 2277, 2502. Vol. 3(ISC-2013), 256-263.
Sesan, A. K., Amos, O. O., & Adeola, F. J. (2016). Effects of indigenous wood specie and plastic/wood ratio on physicomechanical properties of wood plastic composites. Int J Sci Res Agric Sci, 3(1), 011-017. http://dx.doi.org/10.12983/ijsras-2016-p0011-0017
Shukla, S. R., Rao, R. V., Sharma, S. K., Kumar, P., Sudheendra, R., & Shashikala, S. (2007). Physical and mechanical properties of plantation-grown Acacia auriculiformis of three different ages. Australian forestry, 70(2), 86-92.
Tomczak, A. R. K. A. D. I. U. S. Z., Jelonek, T. O. M. A. S. Z., Jakubowski, M. A. R. C. I. N., Grzywinski, W., & Kryger, G. R. Z. E. G. O. R. Z. (2015). Weight and green density of birch pulpwood harvested from the selected stands of Kaczory Forest Inspectorate. Annals of Warsaw University of Life Sciences-SGGW. Forestry and Wood Technology, 91.
Tyree, M. T., Zimmermann, M. H., Tyree, M. T., & Zimmermann, M. H. (2002). Conducting units: Tracheids and vessels. Xylem structure and the ascent of sap, 1-25. https://doi.org/10.1007/978-3-662-04931-0_1
Woode, E., Poku, R. A., Ainooson, G. K., Boakye-Gyasi, E., Abotsi, W. K. M., Mensah, T. L., & Amoh-Barimah, A. K. (2009). An evaluation of the anti-inflammatory, antipyretic and antinociceptive effects of Ficus exasperata (Vahl) leaf extract. Journal of pharmacology and Toxicology, 4(4), 138-151.
Yang, Q., Gao, C., Liu, K., Zhu, Y., & Wang, J. (2022). Compressive Strength of Aged Timber Members in Traditional Building: Considering Differences in Heartwood and Sapwood. Applied Sciences, 12(15), 7719. https://doi.org/10.3390/app12157719
Zheng, J., & Martínez-Cabrera, H. I. (2013). Wood anatomical correlates with theoretical conductivity and wood density across China: evolutionary evidence of the functional differentiation of axial and radial parenchyma. Annals of Botany, 112(5), 927-935. https://doi.org/10.1093/aob/mct153
Zhu, J. Y., Vahey, D. W., Scott, C. T., & Myers, G. C. (2008). Effect of tree-growth rate on papermaking fibre properties. Appita: Technology, Innovation, Manufacturing, Environment, 61(2). Effect of Tree-growth Rate on Papermaking Fibre Properties | Appita: Technology, Innovation, Manufacturing, Environment (informit.org)
Zobel, B. J., & Jett, J. B. (2012). Genetics of wood production. Springer Science & Business Media. Pages 2-10. Genetics of Wood Production - Bruce J. Zobel, Jackson B. Jett - Google Books
Downloads
Published
How to Cite
Issue
Section
License
Copyright (c) 2024 Prosper Mensah, Francis Wilson Owusu, Joshua Kwasi Adzigodie, Felix Boakye, Emmanuel Minkah

This work is licensed under a Creative Commons Attribution 4.0 International License.