Numerical Investigation of Sand Erosion Effects on the T-56 Compressor Blade with Changing Parameters

Authors

  • Nizar A. Qattan
  • Belkacem Kada
  • Ali M. Al-Bahi

DOI:

https://doi.org/10.14738/tmlai.1302.18449

Keywords:

computational fluid dynamics, turbomachinery, transonic compressor, T-56 engine compressor, transport equations, Eulerian approach, Turbulence models, shear stress transport model, Fin-nie’s Model

Abstract

This paper presents a comprehensive numerical investigation into the effects of sand erosion on the T-56 compressor blade, a critical component in turbomachinery subjected to harsh environmental conditions. Using advanced Computational Fluid Dynamics (CFD) techniques, the study examines the impact of parameters such as sand particle concentration, size, and pressure ratio on blade erosion rates and overall compressor performance. The numerical analysis is validated against established NASA Rotor 37 data, providing confidence in the accuracy of the modeling approach. Results reveal the significant influence of sand erosion on aerodynamic efficiency and highlight key operational considerations to mitigate damage in sandy environments. This research provides valuable insights for improving the design and maintenance of turbomachinery, particularly in regions like the GCC, where sand ingestion poses a severe challenge.

References

Rolls-Royce corporation, ‘T-56/50D Desert operation presentation Engine safety brief.’, Dallas.

M. Suzuki, K. Inaba, and M. Yamamoto, ‘Numerical simulation of sand erosion phenomena in rotor/stator interaction of compressor’, Journal of Thermal Science, vol. 17, pp. 125–133, 2008.

M. Suzuki and M. Yamamoto, ‘Numerical simulation of sand erosion phenomena in a single-stage axial compressor’, Journal of Fluid Science and Technology, vol. 6, no. 1, pp. 98–113, 2011.

S. Elfeki and W. Tabakoff, ‘Erosion Study of Radial Flow Compressor with Splitters’, in Turbo Expo: Power for Land, Sea, and Air, American Society of Mechanical Engineers, 1986, p. V003T05A002.

J.-P. Immarigeon, D. Chow, V. R. Parameswaran, P. Au, H. Saari, and A. K. Koul, ‘Erosion testing of coatings for aero engine compressor components’, Advanced Performance Materials, vol. 4, pp. 371–388, 1997.

E. N. Kablov and S. A. Muboyadzhyan, ‘Erosion-resistant coatings for gas turbine engine compressor blades’, Russian Metallurgy (Metally), vol. 2017, no. 6, pp. 494–504, Jun. 2017, DOI: 10.1134/S0036029517060118.

M. W. Reedy, T. J. Eden, J. K. Potter, and D. E. Wolfe, ‘Erosion performance and characterization of nanolayer (Ti,Cr)N hard coatings for gas turbine engine compressor blade applications’, Surf Coat Technol, vol. 206, no. 2–3, pp. 464–472, Oct. 2011, DOI: 10.1016/j.surfcoat.2011.07.063.

J. S. Litt and D. L. Simon, ‘Toward a real‐time measurement‐based system for estimation of helicopter engine degradation due to compressor erosion’, Journal of the American Helicopter Society, vol. 54, no. 1, p. 12008, 2009.

A. Hamed, W. Tabakoff, and D. Singh, ‘Modeling of compressor performance deterioration due to erosion’, International Journal of Rotating Machinery, vol. 4, no. 4, pp. 243–248, 1998, DOI: 10.1155/S1023621X98000207.

W. Tabakoff, A. N. Lakshminarasimha, and M. Pasin, ‘Simulation of compressor performance deterioration due to erosion’, J Turbomach, vol. 112, no. 1, pp. 78–83, 1990, Doi: 10.1115/1.2927424.

W. Tabakoff, ‘Performance Deterioration’, 2014.

N. A. Qattan, A. M. Al-Bahi, and B. Kada, ‘Simulation of Transonic Compressor Performance Deterioration Due to Sand Erosion’. [Online]. Available: http://asrjetsjournal.org/

H. K. Versteeg and W. Malalasekera, An introduction to computational fluid dynamics: the finite volume method. Pearson education, 2007.

K. V Pagalthivarthi, P. K. Gupta, V. Tyagi, and M. R. Ravi, ‘CFD predictions of dense slurry flow in centrifugal pump casings’, International journal of aerospace and mechanical engineering, vol. 5, no. 4, pp. 16–28, 2011.

G. Brown, ‘Use of CFD to predict and reduce erosion in an industrial slurry piping system’, in Fifth International Conference on CFD in the process industries. CSIRO, Melbourne, Australia, 2006, pp. 13–15.

G. J. W. Van Bussel, ‘The science of making more torque from wind: Diffuser experiments and theory revisited.’, in Journal of Physics: Conference Series, IOP Publishing, 2007, p. 012010.

M. Saeed and M.-H. Kim, ‘Airborne wind turbine shell behavior prediction under various wind conditions using strongly coupled fluid structure interaction formulation’, Energy Convers Manag, vol. 120, pp. 217–228, 2016.

M. O. L. Hansen, N. N. Sørensen, and R. G. J. Flay, ‘Effect of placing a diffuser around a wind turbine’, Wind Energy: An International Journal for Progress and Applications in Wind Power Conversion Technology, vol. 3, no. 4, pp. 207–213, 2000.

F. R. Menter, ‘S. Eloret Institute, Zonal two equation kappa-omega turbulence models for aerodynamic flows’, in 24th Fluid Dynamics Conference, 1993.

I. M. Hutchings, ‘Mechanical and metallurgical aspects of the erosion of metals’, in Corrosion/Erosion of Coal Conversion Systems Materials Conference, 1979, pp. 393–428.

I. Finnie, ‘Some observations on the erosion of ductile metals’, wear, vol. 19, no. 1, pp. 81–90, 1972.

C. F. X. Ansys, ‘CFX-Pre user’s guide release 16.0’, Ansys Inc.: Canonsburg, PA, USA, 2015.

S. Z. Roshan, S. Alimirzazadeh, and M. Rad, ‘RANS simulations of the stepped duct effect on the performance of ducted wind turbine’, Journal of Wind Engineering and Industrial Aerodynamics, vol. 145, pp. 270–279, 2015.

Downloads

Published

2025-04-25

How to Cite

Qattan, N. A., Kada, B., & Al-Bahi, A. M. (2025). Numerical Investigation of Sand Erosion Effects on the T-56 Compressor Blade with Changing Parameters. Transactions on Engineering and Computing Sciences, 13(02), 62–83. https://doi.org/10.14738/tmlai.1302.18449