Coupled Statistical–Numerical Framework for Predicting Droplet Temperature in Gas Metal Arc Welding

Authors

  • Victor Avokerie Ijoni Department of Production Engineering University of Benin, Benin City, Nigeria http://orcid.org/0009-0000-9760-4836
  • Joseph Ifeanyi Achebo Department of Production Engineering University of Benin, Benin City, Nigeria
  • K. O. Obahiagbon Department of Production Engineering University of Benin, Benin City, Nigeria
  • F. O. Uwoghiren Department of Production Engineering University of Benin, Benin City, Nigeria

DOI:

https://doi.org/10.14738/tmlai.1306.19600

Keywords:

Gas Metal Arc Welding (GMAW), Droplet Temperature, Response Surface Methodology (RSM), Finite Difference Method (FDM), MATLAB, Thermal Simulation, Welding Process Optimization

Abstract

Accurate prediction of droplet temperature during Gas Metal Arc Welding (GMAW) is crucial for controlling metallurgical outcomes and process stability, yet direct measurement remains a challenge due to the rapid thermal dynamics involved. This study aims to develop and validate both empirical and physics-based models to estimate droplet temperatures during GMAW. A total of 20 experimental runs were performed using mild steel (AISI 1018) under a Central Composite Design (CCD), varying welding current (240–270 A), voltage (23–26 V), and wire feed rate (2.4–3.0 mm/s). Droplet temperatures were measured with a high-resolution pyrometer and modeled using Response Surface Methodology (RSM) in Design Expert and a 1D Finite Element Method (FEM) implemented via MATLAB. The RSM model showed high accuracy with an RMSE of approximately 4.3 °C compared to experimental results, while the 1D FEM model achieved an RMSE of 192.7 °C, capturing the general thermal trend despite simplifications such as constant properties and 1D heat conduction. These findings demonstrate the complementary strengths of empirical and computational approaches: RSM offers precise data-driven predictions, while FEM provides a deeper physical understanding of heat transfer during droplet formation.

References

Otimeyin, A. W., Achebo, J. I., & Frank, U. (2025). Advanced Modeling and Optimization of Weldment Responses Using Statistical and Metaheuristic Techniques. American Journal of Mechanical and Materials Engineering, 9 (1), 25-36. https://doi.org/10.11648/j.ajmme.20250901.13

Erhunmwun, I.D. and Etin-Osa, C.E. (2019): Temperature distribution in centrifugal casting with partial solidification during pouring. Materials and Engineering Technology, ISSN: 2667-4033.

Etin-Osa, C.E. and Achebo, J.I. (2017): Analysis of optimum butt welded joint for mild steel components using FEM (ANSYS). American Journal of Naval Architecture and Marine Engineering, 2(3), pp. 61-70.

Rosenfeld, S. & Shorr, S. (2003). Heat transfer and temperature distribution in welding of carbon steels. Journal of Heat Transfer, 125(3), 555–561.

Liu, X. & Liu, Z. (2011). A study on the temperature distribution of the welded joints in the arc welding process. International Journal of Thermal Sciences, 50(7), 1253–1260.

Xie, L. & Yang, J. (2014). Numerical simulation of the transient temperature field in welding. Computational Materials Science, 83, 106–115.

Beaumont, P., & Marani, S. (2017). A comprehensive review of finite element modeling of welding residual stresses. International Journal of Pressure Vessels and Piping, 152, 1-10.

Jin, T., & Li, Y. (2012). Finite difference method for heat conduction problems in welding. Journal of Manufacturing Processes, 14(3), 358–365.

Lal, A., & Pathak, R. (2016). Application of response surface methodology in welding process optimization: A review. Materials & Design, 90, 658–668.

Gokhan, K., & Cakir, M. (2013). Optimization of welding parameters using response surface methodology (RSM) in GMAW. Materials & Design, 45, 507–515.

Vignal, V., & Dufresne, S. (2015). Comparison of FEM, RSM, and experimental results for welding simulation. Journal of Manufacturing Science and Engineering, 137(2), 021017.

Kwak, H., & Lee, K. (2008). Coupling finite element and response surface methods for the prediction of welding temperature field and residual stress. International Journal of Advanced Manufacturing Technology, 36(9-10), 961–973.

Matsui, T., & Watanabe, K. (2010). Welding simulation using finite element analysis and experimental validation. Welding Journal, 89(1), 17–23.

Etin-Osa, E.C. and Ogbeide, O.O. (2021): Optimization of the weld bead volume of tungsten inert gas mild steel using response surface methodology. NIPES Journal of Science and Technology Research, 3(4), pp. 314-321.

Imhansoloeva, N.A., Achebo, J.I., Obahiagbon, K., Osarenmwinda, J.O., and Etin-Osa, C.E. (2018): Optimization of the deposition rate of tungsten inert gas mild steel using response surface methodology. Scientific Research Publishing, 0, pp. 784-804.

Ogbeide, O.O. and Etin-Osa, E.C., (2023). Prediction of hardness of mild steel welded joints in a tungsten inert gas welding process using artificial neural network. JASEM, 27(11), pp.2381-2386.

Downloads

Published

2025-11-20

How to Cite

Ijoni, V. A., Achebo, J. I., Obahiagbon, K. O., & Uwoghiren, F. O. (2025). Coupled Statistical–Numerical Framework for Predicting Droplet Temperature in Gas Metal Arc Welding. Transactions on Engineering and Computing Sciences, 13(06), 57–68. https://doi.org/10.14738/tmlai.1306.19600